How To Make A Rain Barrel 2023

rain barrel
rain barrel

Rain Barrel: Americans are consuming more water every year.

In fact, according to the Environmental Protection Agency, the average family consumes 330 gallons of water per day. In this usage in summer can reach 1,000 gallons.

Fortunately, there is an easy way to reduce our water bills and water footprints.

DO READ: 9 Easy Ways to Recycle Old Furniture in 2023

Rain barrels collect water using tubes or gutters (downspout) under the roof, which are directed through the diverter to the barrel. The water passes through a screen that captures most of the debris.

Then you can use water in plants and orchards, or even drink it during dry spells. In general, these kegs are the most effective way to save water at home.

Fortunately, you can make and install a rain barrel in less than an hour.

Materials and tools To Make A Rain Barrel

  1. Measuring Tape
  2. Landscape fabric
  3. Hose clamp
  4. Utility knife or hacksaw
  5. Diverter
  6. Pencil
  7. Spigot
  8. Rubber and metal washer
  9. Pencil
  10. Drill
  11. Water repellent sealant

13 Steps To Make A Rain Barrel

rain barrel
rain barrel
  • Locate a place you want to keep your rain barrel, if possible just below a downspout. Then place it on a high flat surface. You can use concrete blocks or bricks.
  • Remove the rain barrel from the elevator and rotate it to the ground. Dig a hole from the edge of the barrel. From here you will draw water from the barrel. The hole on the tap should be slightly smaller than the hole.
  • Add rubber and metal washers to the tap.
  • Place a waterproofing material around the rubber washer. Put it inside the hole and hold it for 20 seconds.
  • Reach inside the barrel and add the rubber and metal washer to the other end of the smooth end. Some owners add hose clamps in case of severe storms. This ensures that the pin stays in place.
  • Cut the inlet opening at the top of the barrel. This is where your diverter or downspout will go. The opening should be large enough to fit the diverter. You can use a knife or a hacksaw to cut.
  • Dig two holes on either side of the barrel. If the rain barrel is full, these holes will release some unnecessary water and pressure.
  • Cut the landscape fabric just enough to fit the rain barrel. These fabrics prevent mosquitoes, leaves, and debris from entering the barrel.
  • Open the cap and place the torn cloth in an open barrel. Close the cap. The fabric should spread a little over all the sides.
  • Cut the downspout to fit the rain barrel.
  • If you add the inverter, measure it and cut off the drain pipe if necessary.
  • Connect the connecting tube to the outlet and place it in the barrel.
  • Test the system by pouring water from the ladder into the gutter. Always hold the ladder. If the water does not get into the barrel, there may be clogging or holes in the downspout or gutter.

Cost Of Rain Barrel

Apart from all the advantages of a rain barrel, they are also affordable.

Although you can visit your local hardware store and buy all the necessary parts and tools, you can also buy a rain barrel set for less than $ 200.

rain barrel
rain barrel

In fact, the standard 60-gallon rain barrel set can vary from 100 to 150, depending on the style

In addition, many cities, water areas, and water conservation agencies offer discounts on rain drums, which reduces the cost of your rain drums. Check with your eligible city or water service if you are eligible.

Conserve water

Did you know that only 1% of our planet’s water is safe to drink? In fact, we can survive for two weeks without food, but only days without water.

Rainwater is the best water you can use for your plants. Treated water contains salts and chemicals harmful to plants. Rainwater contains the nutrients and minerals your garden will love.

As you can see, collecting water from natural resources not only saves you money and improves your health, but also keeps our environment safe and secure.


Please enter your comment!
Please enter your name here